一、入水：gate

進入位：　gate location

水口形式：gate type

大水口：edge gate

細水口： pin-point gate

水口大?。篻ate size

轉水口：　switching runner/gate

唧嘴口徑：　sprue diameter

二、流道: runner

熱流道：　hot runner,hot manifold

熱嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圓形流道：round(full/half runner

流道電腦分析：mold flow analysis

流道平衡:runner balance

熱嘴：　hot sprue

熱流道板：hot manifold

發熱管：cartridge heater

探針: thermocouples

插頭：　connector plug

插座： connector socket

密封/封料： seal

三、運水：water line

喉塞：line lpug

喉管：tube

塑膠管：plastic tube

快速接頭：jiffy quick connector plug/socker

四、模具零件：　mold components

三板模：3-plate mold

二板模：2-plate mold

邊釘/導邊：leader pin/guide pin

邊司/導套：bushing/guide bushing

中托司：shoulder guide bushing

中托邊L：guide pin

頂針板：ejector retainner plate

托板：　support plate

螺絲： screw

管釘：dowel pin

開模槽：ply bar scot

內模管位：core/cavity inter-lock

頂針：　ejector pin

司筒：ejector sleeve

司筒針：ejector pin

推板：stripper plate

縮呵：movable core,return core core puller

扣機（尼龍拉勾）：nylon latch lock

斜頂：lifter

模胚（架）： mold base

上內模：cavity insert

下內模：core insert

行位（滑塊）： slide

鑲件：insert

壓座/斜雞：wedge

耐磨板/油板：wedge wear plate

壓條：plate

撐頭: support pillar

唧嘴： sprue bushing

擋板：stop plate

定位圈：locating ring

鎖扣：latch

扣雞：parting lock set

推桿：push bar

栓打螺絲：S.H.S.B

頂板：eracuretun

活動臂：lever arm

分流錐：spure sperader

水口司:bush

垃圾釘：stop pin

隔片：buffle

彈弓柱：spring rod

彈弓:die spring

中托司：ejector guide bush

中托邊：ejector guide pin

鑲針：pin

銷子：dowel pin

波子彈弓：ball catch

喉塞: pipe plug

鎖模塊：lock plate

斜頂：angle from pin

斜頂桿：angle ejector rod

尼龍拉勾：parting locks

活動臂：lever arm

復位鍵、提前回桿：early return bar

氣閥：valves

斜導邊：angle pin

術語：terms

承壓平面平衡：parting surface support balance

模排氣：parting line venting

回針碰料位：return pin and cavity interference

?？偢叱銎C規格：mold base shut hight

頂針碰運水：water line interferes withejector pin

料位出上/下模：part from cavith (core)side

模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.

不準用鑲件： Do not use (core/cavity) insert

用鈹銅做鑲件： use beryllium copper insert

初步（正式）模圖設計：preliinary (final) mold design

反呵：reverse core

彈弓壓縮量：spring compressed length

穩定性好：good stability,stable

強度不夠：insufficient rigidity

均勻冷卻：even cooling

扣模：sticking

熱膨脹：thero expansion

公差：tolorance

銅公(電極）：copper electrode